Grand Admiral here. I probably get "who are you," "which movie are you in," and "will you take a picture for us" most often. Occasionally someone will call me director. I've also been called "like Thrawn," which was amusing and essentially accurate, and "Mrs. Thrawn" which I'll gladly accept. I have been thanked for my service and asked for directions multiple times. Once, someone commented on a picture of me seated in the emperor's throne, flanked by two death troopers, with "Are you in the Air Force, or is that a cosplay?" Thinking the death troopers would make my sarcasm kind of obvious, I replied "Space Force." The only response to that was "cool."
Police officer is the more common one, particularly since Victoria Police changed their uniform to a very dark NYPD style - I wear a staff Officer costume.
Have been confused for a security guard at a Lego show, and someone wearing a period chauffeur costume at a car show (never get separated from the rest of your troopers lol).
Naturally I’ve had the ever unsavoury “Nazi”. Always an unpleasant association.
Never been called any names yet, don’t want too. I was at a Troop event last year in Victoria Australia at Children’s Christmas Party, arrived in style as Krennic and nobody knew who I was. Oh dear
Thought everyone has seen Rogue One
The visual guide refers to Lt Putna as a “librarian-turned-security-officer”, so why not just called the black uniformed R1/Solo CRL “Security Officer (R1/Solo)”? It helps makes a clear delineation between the OT and the Anthology uniforms.
Your concern would be absolutely valid, but fortunately, that's not the way we've planned this to work. We're not simply "renaming" the old CRL, while simultaneously making these significant changes.
Instead, previously-approved members will still have the designation of "Staff Officer (Black)". No change. That designation will simply no longer be available for new approvals (once the generous grace period ends).
New approvals will have the option of ANH Staff Officer (if that's the costume they have), or this new one, whatever it's ultimately named.
Wow, that's a lot of variations but then again there were quite a few manufacturers as well!
I have a German green woolen one dating from 1944 and a Swedish black one from a later period but exactly the same style, would love to wear my black one over the staff officer but its too hot!
I’ve been meaning to do one of these threads for a while now, and finally had a good excuse to make a new rank bar, so here goes.
Push button rank bars are the ideal. Screen-accurate, and just look way better than the cheap acrylic chip styles. And best of all, they can be hand made at home very inexpensively and with just a few basic tools! There are a LOT of photos here, detailing every step, but it’s a pretty straightforward process, as a whole.
There are also a LOT of steps here but don't be scared off... it's just because I broke each step to the nth degree, and a lot of steps are just double, triple, quadruple-checking measurement and alignment. This is all really simple stuff that nearly anyone should be able to do, and nothing more exotic than a hacksaw, sandpaper and an exacto knife (or something similar, even) is really required (plus glue, of course). And the hacksaw is probably optional, if you get the shop to do the first cut. Oh, and a ruler, of course.
HERE'S HOW:
Note: E6000 is the glue of choice. Know it, love it, use it. It takes 24 hours to cure, and I don’t recommend shorting that at ALL. BUT: I recommend starting the gluing either in the morning, so you can do some final manipulation in the evening, or in the evening, so you can do that final manipulation in the morning. (I usually just glue at night so I can tweak it in the morning, then let it finish curing through the day, and put it all together the next evening.)
Step one: The Buttons
Buy the appropriate push buttons for your costume.
TIP: See this thread for details on how and where they can be purchased:
Step two: The Bar
Buy a piece of aluminum stock. I prefer the 1/8” stuff, some people like the thinner 1/16” stuff. I just think the thinner stuff bends far too easily. You can get a long piece at Home Depot, Lowe’s, ACE, or really almost any hardware store. You can get 4’ of the stuff for around $10. That's quite a few rank bars, even if they're all the largest 6" size. So make some for a friend, or make yourself a variety so you can choose ranks like you pick socks for the day, LOL
Figure out how long it needs to be, based on how many buttons you’ll be using, and how far apart they are. Add the same spacing on each end, and I usually add a millimeter or two of extra length, because it’s easier to sand a little more off than to add more, if anything happens during the finishing process. Especially if the end cut is not perfect. Rogue One buttons, as pictured below, should be 3mm apart. The smaller OT buttons should be about 1/4" (~6mm) between them. See the Imperial Rank Bar databank page for details. (Note: That page needs updating with Rogue One/Solo info... it's being worked on) I'm using millimeters in this guide... I find them easier to work with for measuring very small distances like this, and most rulers have both measurements anyway.
I do this by literally just setting the buttons on the bar, starting from the end, and measuring out along a ruler. Very simple. Mark a line somewhere where you need to cut.
Step four: Cut the Aluminum
To cut the aluminum, I just use a hacksaw in a miter box. Aluminum is really soft and easy to cut, but if you don’t have a hacksaw, most hardware stores will do at least one cut on for you, so plan ahead and bring your measurements. (Be sure to pad the numbers because they’re not usually super precise about their cuts!)
Step five: Rough sand the bar
Sand the ends down to the exact size you want, within about a millimeter. I use my bench grinder for this, but it can be done by hand with just some sandpaper if you don’t have one. Rough sandpaper is fine at this stage (100-200 grit, whatever), because you’ll be cleaning it up with finer sandpaper in the next step.
Step six: Fine finishing of the bar
Next we clean it up, get rid of any visible scratches (common with plain bar stock from big box stores, since aluminum is soft and it gets beat up a lot), and generally make it nice. For this I use a high grit sandpaper, like 500 grit, and use one that’s rated for wet sanding, because it gives a much better final product very easily. You want a nice perfectly flat surface for this… I use the counter of the bathroom or kitchen sink, because it’s an easy place to do it. The aluminum powder sanded off can then be washed away quickly and easily, and the counter tends to be a perfectly flat surface. (perfect another for this, anyway… as long as you’re not talking aerospace parts, it’s fine) Just put a little dribble of water on the sandpaper and scrub back and forth until it’s clean and smooth. Clean up the ends, too, while you’re at it. I don’t spend much time on the back, since it’s never seen, but sometimes I’ll hit it a little if I feel inclined.
Some like to use a straight edge to sand along so the lines are perfectly horizontal, but it the final finish is smooth enough, that’s not something I care about. Here’s the final bar, for this badge:
Step seven: Measure
I’m a big fan of measuring, measuring, measuring, at multiple times throughout this process, because you really want this as perfect as possible. Shortcut that if you want, but don’t blame me if your badges are less than perfect. So I lay out the buttons, again, on the final bar, and double check everything lays the way I want, including the right amount sticking out on the sides.
Step eight: Button disassembly
Now we’re onto the buttons themselves. Remove the white inserts (just gently squeeze the legs and they should come right out).
Step nine: Button trimming
Next cut off those little legs. You can use any number of tools for this. I’ve used hot knives, utility / box knives Exacto knives, diagonal snips… currently my favorite method is the cutoff wheel on my Dremel:
Step ten: Button cleanup
Then I clean up the inside with the Exacto knife.
Cleaning up a lot doesn’t matter a whole lot, since its on the back and inside, but I’m a perfectionist that way. It does need to be perfectly cut away, though, so they lay perfectly flat. Extra plastic from the pins in the middle that make it rock back and forth is NOT what you want. Be careful not to take too much away… the covers clip in the middle indent, so that needs to be there, and you don’t want a big gap in the middle that lets the glue seep out, either. At the end, I take a couple of quick swipes on that wet sandpaper again… just a couple, though. You don’t want to remove much material here.
Step eleven: More measuring
Lay the inserts out on the bar again, and gently set the button covers on them so you can space them out and measure the distance again. BE CAREFUL NOT TO PRESS THE BUTTON COVERS ONTO THE INSERTS FROM HERE UNTIL THE VERY END!!! Without the legs, those inserts are a REAL b#$%* to remove.
Step twelve: Reference tape
Once everything is, again, laid out perfectly, use a strip of painters tape to carefully slide under the button covers (remember, they’re not pressed on, so they’re held a millimeter or two above the surface of the bar), flush against the inserts. This is going to be your alignment guide to make sure the inserts are perfectly positioned at the right height, so they’re nice and centered on the bar. (top to bottom)
Step thirteen: Double-check the line
Sanity check your tape alignment to make sure it’s nice and straight… it’s funny (not funny) how obvious a millimeter off looks, once everything is put together. The slant is a lot more obvious than you’d think. I tweaked the line just slightly after I took this photo, FWIW, since the left edge looks a hair lower than the right.
Step fourteen: Space out the buttons
Lay out the buttons covers out on their face AGAIN (upside down), on either a piece of paper, paper towel, or some other protective surface you don’t want glue on your nice dining room table, or even your workbench), carefully measured out, and with the inserts lightly placed inside. (REMINDER: BE CAREFUL NOT TO PRESS THEM INTO THE COVERS!)
Step fifteen: Use tape to hold the button insert underside
Now the interesting part begins. Tape a piece of painters tape (I like 1” for this)and gently lay it onto the undersides of the inserts. You should be able to lift the inserts out and have them stay in the exact position they were in when you flip it over. Measure them all AGAIN and confirm everything is as straight as it should be.
Step sixteen: Use tape to hold the button insert from the top
Take ANOTHER piece of painters tape and lay it over the TOP of those inserts. Again, this should lock them into place and hold them nice and firmly. Give yourself a good extra inch or so on either side, because later you’ll want to wrap the ends around the bar to hold things in place.
Step seventeen: Release the button insert underside
Flip it over and remove the tape from the bottom, and you have all the covers nice and in place, ready for gluing.
Step eighteen: Fill the inserts with Glue
And now we glue. Use E6000 or similar slow cure, self-leveling glue. Fill each insert entirely, but be careful not to OVER-fill them.
Step nineteen: Top off the glue levels
Double check they’re completely filled, and add a little more if any corners aren’t fully filled, etc.
Step twenty: Apply the bar
Now remember that bar stock with the tape along the edge? Put that tape line right up against the buttons covers filled with glue. You should feel it easily when the tape line touches the inserts.
Step twenty-one: Flip the inserts and bar
Flip it over so the glue will go down and glue the inserts onto the bar. Double-check your alignment against that alignment tape, now that you can see it easier. You should see pretty clearly that they’re all neatly pressed against the tape reference line, and you’ll know they’re just where they should be as a result.
Step twenty-two: Remove the alignment tape and package it up for the night
At this point, once I’m sure everything is where I want it, I fold the ends of the top painters tape under the bar, to hold everything exactly in place. Remove the alignment tape and wrap it round the middle, like a belt holding it all together.
Step twenty-three: Walk away...
Leave it all out to cure overnight. You’ll want probably 10-14 hours of cure time before the next step.
Step twenty-four: Double-check alignment and measurements
After about 10-14 hours have passed, the glue will be about perfect for the next step. Too long and it’s hard to move things around, if small adjustments are needed. Too short a time, and things can just move out of place again. 10-14 hours is the perfect level of tacky but no longer slippery.
Carefully remove all the tape, and gently place the button covers on the inserts again, so you can truly measure the final positions. (don’t lock them on, remember!) While you CAN measure just the inserts, I find the nice sharp edges of the button covers area easier to measure, and the sharp lines make it more clear if anything is off.
Step twenty-five: More measuring checks
Remove the button covers and AGAIN make sure everything is aligned perfectly, and the measurements between each are perfectly consistent. Again, a half millimeter will be visibly obvious once it’s all done, so this is your last chance to fix things. If anything is off, you should be able to carefully push the inserts around as needed. The glue will allow movements without screwing anything up, at this stage. Be sure to use a straightedge to make sure everything is *perfectly* straight.
Step twenty-six: Glue cleanup
If any glue seeped out from under the inserts, now is the perfect time to clean it up. The glue is still soft enough to be easy to remove with an exacto knife, and not cured hard yet, but not so soft that it just squishes around under the blade. Be careful not to move anything around while you do this, but it should be fairly set in place, as long as you work gently. Cutting right along the edge of the inserts will scratch the bar, but not in a visible area, since the button covers will go over this area.
Step twenty-seven: Walk away again...
Now leave it somewhere safe and walk away for another 10-14 hours. The glue will cure more fully during this time, but it’s no longer so slippery that it’s likely to move out of place on it’s own.
Step twenty-eight: Attach the button covers
After a full 24 hours from the initial gluing has passed, all your work pays off. Visually look it over one last time, measure AGAIN if you want, and then you can proceed to snap the button covers fully onto the inserts, and enjoy your beautiful new rank bar.
Step twenty-nine: Apply the backing
The timing of the very last step is up to you. The glue SHOULD be pretty set at this point, but I still like to be careful (there’s a lot of glue in an enclosed space, in there). E6000 fully cures in 72 hours, so that’s my preferred time to proceed, but it really depends on how much of a hurry you’re in. I’ve done the last step sooner and been fine, just try to be gentle with the buttons a bit longer, and don’t leave them anywhere where anything is pressing on them.
But the last step is to attach whatever attachment method you’re using to the back. I use simple self-adhesive magnet bars from Amazon (see the DIY push button source thread linked at the top of this post). Just peel off the sticker backing and stick on the back of the rank bar, and you’re done. (I put something moderately heavy on top for a couple minutes to really stick the sucker on there) Some prefer push pins, which would need to be epoxied into place, but that’s all up to the end user)
Step thirty: There is no step thirty
Et fini. You're done. Stick on your costume and rock that rank!
Yes, those hats look very tall! As to those trenchcoats they are very similar in design but possibly of a lighter material as the German ones were leather no?
I get it for sure. There have been CRLs that I have found to be overly pedantic in my opinion. But I had to deny people because of them. *Cough!* Biker Scout! *Cough!*
That’s a good question! Let me have a try...
I’ve added the tile size to suit R1/Solo also. Sorry I don’t know inch fractions!
I feel leaving a range for the tile spacing at L1 allows a little freedom between makers, self-builders etc.
Just my thoughts on this of course.
(Sorry about formatting. I’m at work and using my iPad)
Worn on the left side of the tunic over the heart.
Rank consists of colored plastic tiles mounted on a single metal or metal looking bar only
The bar is 1" (25.4 mm) height.
Rank tile dimensions may be either:
- 1/2" (12.7 mm)width x 3/4" (19 mm) height and about 1/8" (3.2 mm
- 15 mm width x 21 mm height and about 1/8" (3.2 mm)
Tiles are mounted with approximately 2.5 - 6.4mm space between them.
Rank tiles are translucent.
Rank tile configuration may be from any licsensed source EXCEPT those ONLY seen in A New Hope.
OPTIONAL Level two certification (if applicable):
Rank consists of colored plastic push buttons mounted on a metal bar.
Rank tiles are the larger Rogue One/Solo style (15 mm width x 21 mm height and about 1/8" (3.2 mm))
Spacing between tiles to be no greater than 3.5mm
Rank bar is a single row.
Rank tile configuration must match those seen in Rogue One or Solo
TK1571 reacted to LadyXythis in Names you've been called
TK1571 got a reaction from shadan in Staff Officer (black uniform) Update
TK1571 got a reaction from tarok in Staff Officer (black uniform) Update
TK1571 got a reaction from kman in Staff Officer (black uniform) Update
TK1571 got a reaction from lantern2745 in Staff Officer (black uniform) Update
TK1571 got a reaction from Hask in Staff Officer (black uniform) Update