AdmiralJag

I've just updated the title of the thread  

@buckrogersbarker can you rename the title of this thread to Imperial Security Bureau Officer (Non saga), or something more in line with what we are doing here?
Thanks!

I've added a bunch of 4K screenshots to the Gallery.  For the time being I've listed the album as "ISB Officers (White and Grey)" because the grey officer IS on Lt Dedra's assistant on staff in her office, so it's possible it's just ISB in another color.  We don't really know for sure if he's just ISB in another color, or actually in a different branch that's somehow connected to ISB, but hopefully time will tell.  I'll adjust the album names at that time, if needed.

It is now apparent that the ISB follows the same rank chart as the Security Services and does have some authority over them.

The ISB Major received reports from Lieutenants and rank was used interchangeably with their title's "Supervisor".   A single Lieutenant can be in charge of as many as 6 to 8 sectors. which is a pretty large territory.

This is a placeholder for all material connected to the grey uniformed officers in Andor.

This is a placeholder for an imperial prison warden

This is a placeholder for the Preox-Morlana Corporate Security Forces Uniforms

Thanks, @AdmiralJag. I legit missed the gloves, so good call on that!
 
Here's the new draft. Awaiting pictures of the trenchcoat and epaulets. 
 
Imperial Hat, Black Hat is OPTIONAL but only if a specific referenced licensed character’s typical uniform configuration is copied in full, and does not typically include a hat. Fabric is a medium weight suiting material matching the pants and tunic if applicable. Cavalry Twill or a Gabardine style weave is most accurate. Base of the hat is conical, with a crown about 4 inches (101.6 mm) tall. Front and rear “flaps” overlap on the sides, with the back flap over the front, and are about 4 inches (101.6 mm) high. Front bill extends 3 inches down, decorated with 5, 6 or 7 concentric stitches. Imperial Code Disk is positioned in the center of the front vertical "flap.  
OPTIONAL Level two certification (if applicable): Code disk has NO notch in it, on the outermost disk.  
   
 
Tunic Fabric should be a medium weight, white suiting material. Tunic is double-breasted with a left over right closure on the tapered yoke. Yoke comes up across the shoulder to the top shoulder seam. The standing collar has square corners and is between 1.25" (31.8 mm) to 2" (50.8) tall dependent on wearers neck size Collar closes snug and includes a modesty panel behind closure. Collar edges are closed with two eye hooks. There are code cylinder pockets on both outside panels of the jacket from about half way between the top and bottom on the arm hole. Sleeves are long, and without decoration, cuffs or buttons. Sleeves contain 2 seams; one along the bottom and one along the back. Tunic is constructed with no top-stitching (stitches visible on the exterior surface of fabric) Hook and eye fasteners on the uniform should not be visible.  
OPTIONAL Level two certification (if applicable): There is a dart of about 2" (50.8 mm) in the top center of the yoke. There is a seam running the entire circumference of the tunic, dividing it along a line hidden by the uniform belt. The back of the tunic has princess seams that run vertically and turn outward to intersect the arm-hole seam at the vertical center. OPTIONAL Level three certification (if applicable): Tunic is secured on the right side by snaps or buttons; not hook and loop fastener (Velcro). There is no top-stitching visible anywhere. A lining is sewn in.  
   
Rank Bar See the Imperial Rank Bar page for more information. Rank consists of colored plastic tiles mounted on a single or double metal or metal looking bar(s). Worn on the left side of the tunic over the heart, aligned with the code cylinder pocket. Each bar is approximately 1 inch (25.4 mm) to 1.25 inches (31.75 mm) in height. Length is determined by chosen rank. Rank tile dimensions and spacing are appropriate and proportional to the sizing of the bar to allow for even spacing from each other and the border of the bar: Rogue One/Solo rank tile dimensions are approximately 15 mm wide, 21 mm tall, and 3.2 mm deep. Original Trilogy/Mandalorian rank tile dimensions are approximately ½ inch (12.7 mm) width x ¾ inch (19 mm) height x 1⁄8 inch (3.2 mm) deep. Rank tile sizes must all be of one or the other — Not to be intermixed. Please note that final dimensions of the bar may be proportional to the wearer. Rank bar corners are a hard 90 degree angle, or slightly rounded. Rank tiles are translucent, rectangular, positioned side by side in a vertical orientation, and evenly spaced. No amber/yellow tiles are present for ISB agents. Color, quantity, and combinations of the tiles/bars are determined by rank and are appropriate to uniform type/color as supported by licensed reference.  
OPTIONAL Level two certification (if applicable): Rank consists of colored plastic push buttons (with white to off white insert) mounted on a metal bar. OPTIONAL Level three certification (if applicable): Chosen rank to match a specific officer seen onscreen or other licensed media.  
   
 
 
Code Cylinders 2 per costume may be worn one in each pocket Modified: silver "chalk holder" tube with short clip, top is colored Blue. Dosimeter style: True Dosimeter with correct clip and Blue top. Ysanne Isard, Code Cylinders are not required.  
OPTIONAL Level two certification (if applicable): Only real or replica dosimeters are used. Dosimeters have a silver, non-brass, clip  
   
 
Belt The belt is constructed from a non-textured leather or a leather-like material. Approximately 2" (50.8 mm) in width, up to 3" (76.2 mm) is acceptable. There are no loops on the belt. A single large snap or rivet is visible approximately 1" (25.4 mm) from the buckle. The belt may be worn with the snap to the right or left of the wearer. The buckle is constructed from a horizontally brushed metal, or metal looking material. The buckle size is approximately 2 ⅛" (66.7 mm) high and 4 ⅛" (104.5 mm) wide with 0.5" (12.7 mm) radius rounded corners. Buckle is adorned with an Imperial Code Disk at the center. Please refer to the Imperial Buckle reference page for information on accurate and inaccurate style buckles.  
OPTIONAL Level two certification (if applicable): Belt is made of leather. Snap is worn to the left of the wearer. Buckle has a slight horizontal curve.  
   
Belt boxes (Non-Saga style) Dimensions are approximately 2 inches (50.8mm) wide by 3 inches (76.2 mm) tall by 1 inch x (25.4mm) thick. Two boxes to be worn vertically, one each on either side of the belt buckle.  
OPTIONAL Level two certification (if applicable): Belt boxes are made of metal.  
   
Jodhpur Trousers, Black Fabric is a medium weight suiting material matching the tunic. Cavalry Twill or a Gabardine style weave is most accurate. Version One trousers are flared riding breeches, with semi-stiff flares to the hip/thigh area. Breeches are worn with boots. Breeches are neatly pressed or ironed without creases. Pockets are acceptable, although must not be visible with the tunic on.  
 
 
Officer Boots Knee-high, black, riding style, lace-less, smooth non-textured, leather or leather-like material. There are no buckles, snap tabs or decoration. Boots have conservative heels. A single stretch panel or zipper may be present, they are to be hidden on the inner part of the boot shaft. Not visible from the front, side or back. The top of the boots may be flat or Spanish Style, but not Cowboy or Super Hero (pointed at the front) style. A small V-shaped notch may be present that the back of the boots top.  
OPTIONAL Level two certification (if applicable): Boots do not have a zipper. OPTIONAL Level three certification (if applicable): Boots are made of leather. Not vinyl or PVC. Exact replicas of English riding (dress) boots or Equestrian boots.  
   
Optional Accessories Items below are optional costume accessories. These items are not required for approval, but if present appear as described below. If adding in an accessory after initial approval, the item still needs to be submitted to local GML for approval before use.
 
Gloves Black, wrist length gloves constructed of a smooth, non-textured leather or leather-like material. Enclosed fingers. No buckles, straps, etc.  
OPTIONAL Level two certification (if applicable): Gloves have a plain back and no visible adornments. Gloves made of leather. Gloves end just past the wrist. OPTIONAL Level three certification (if applicable): Gloves have a notch centered in the edge below the palm. Slit may be straight or rounded.  
   
200x150px Epaulets, Silver Silver, colored strips, firmly attached on the edge of each shoulder. The strips are matte or metallic in finish and made with a semi-rigid to rigid material. The strips have a small raised ridge around the edge. The strips are no more than 1.25 inches in width. Positioned across the collar bone where the shoulder begins, between the shoulder seam and yoke seam. The strips do not overlap the seams they sit between.  
OPTIONAL Level two certification (if applicable): The lower limit of the strip, in positioning, should run parallel to the lowest point of the center of the collar. OPTIONAL Level three certification (if applicable): Have a metallic sheen.  
   
200x150px Trenchcoat Made of a medium-weight waterproof fabric that is cream-ecru in color. Fabric has a matte finish. Two flares at the breast overlap and close in the front, left breast over right. The collar continues around the neck and is approximately 3.5 inches wide. A seam runs down the arm on the outside, it begins at the costumer’s collar. Two inch long cuffed sleeves with a single button towards the end of the cuff. The cuff “strap” ends in a chevron shape. On the back, the storm shield has a pinch pleat at the top center of the shoulders. The coat ends mid-calf and is straight cut along the bottom edge. The coat below the belt has a split seam in the back. Two pocket flaps may appear at the costumer’s hip, but are not required; if present, there should be no visible pocket stitching. The coat is worn either belted with the standard leather officer's belt, or loose.  
 
Holster Made of black leather or leather-like material.  
OPTIONAL Level two certification (if applicable): Holster is affixed via a single loop over the belt. Holster is made of leather.  
   
SE-14R Light Repeating Blaster The barrel detailing is evident with the cocking lever and slider in place. The ejection port is also evident. The scope mount looks similar to the magazine but smaller in size. The scope does not protrude past the blaster body.  

So, next project, republic Medic

All of this is basically written.
Keep in mind that the V3 ISB agent is turning into the non saga. It's being updated to mirror the other non saga costumes. 
 
I guess I can post a draft LOL
Here's what we are looking at.
The trenchcoat is not in there yet cause I don't have any pictures. I'm also waiting on a photoshop edit for the epaulets.
 
 
http://www.501st.com/include/images/crlblackhd.gif   Imperial Security Bureau Officer (Non saga) Model ID-23008, Photo by S.Ofner    
Description: Imperial Security Bureau Officer (Non saga)
Prefix: ID
Detachment: Imperial Officer Corps
Context: Rogue One, Andor, and comics.
The Imperial Security Bureau is a law enforcement and internal intelligence organization of the Galactic Empire. The ISB has the the responsibility of encouraging the populace and military personnel to remain obedient to Imperial policy and ideals. The largest branch of the ISB is Surveillance. Other branches include Investigation, Internal Affairs, and Interrogation. This configuration is seen in Rogue One, Andor, and as Ysanne Isard in comic form.
   
For 501st membership only the requirements in black need to be met.
The Imperial Officer Corp Detachment defines additional, optional levels of costuming excellence. In the page below, items listed in blue are optional features that will improve the quality of the costume. Items listed in red are intended to further enhance the finished costume. Please visit the Detachment website for more specific details.
 
This CRL is a work in progress and is not yet ready to use for any approval!
   
Imperial Hat, Black Hat is OPTIONAL but only if a specific referenced licensed character’s typical uniform configuration is copied in full, and does not typically include a hat. Fabric is a medium weight suiting material matching the pants and tunic if applicable. Cavalry Twill or a Gabardine style weave is most accurate. Base of the hat is conical, with a crown about 4 inches (101.6 mm) tall. Front and rear “flaps” overlap on the sides, with the back flap over the front, and are about 4 inches (101.6 mm) high. Front bill extends 3 inches down, decorated with 5, 6 or 7 concentric stitches. Imperial Code Disk is positioned in the center of the front vertical "flap.  
OPTIONAL Level two certification (if applicable): Code disk has NO notch in it, on the outermost disk.  
   
 
Tunic Fabric should be a medium weight, white suiting material. Tunic is double-breasted with a left over right closure on the tapered yoke. Yoke comes up across the shoulder to the top shoulder seam. The standing collar has square corners and is between 1.25" (31.8 mm) to 2" (50.8) tall dependent on wearers neck size Collar closes snug and includes a modesty panel behind closure. Collar edges are closed with two eye hooks. There are code cylinder pockets on both outside panels of the jacket from about half way between the top and bottom on the arm hole. Sleeves are long, and without decoration, cuffs or buttons. Sleeves contain 2 seams; one along the bottom and one along the back. Tunic is constructed with no top-stitching (stitches visible on the exterior surface of fabric) Hook and eye fasteners on the uniform should not be visible.  
OPTIONAL Level two certification (if applicable): There is a dart of about 2" (50.8 mm) in the top center of the yoke. There is a seam running the entire circumference of the tunic, dividing it along a line hidden by the uniform belt. The back of the tunic has princess seams that run vertically and turn outward to intersect the arm-hole seam at the vertical center. OPTIONAL Level three certification (if applicable): Tunic is secured on the right side by snaps or buttons; not hook and loop fastener (Velcro). There is no top-stitching visible anywhere. A lining is sewn in.  
   
Rank Bar See the Imperial Rank Bar page for more information. Rank consists of colored plastic tiles mounted on a single or double metal or metal looking bar(s). Worn on the left side of the tunic over the heart, aligned with the code cylinder pocket. Each bar is approximately 1 inch (25.4 mm) to 1.25 inches (31.75 mm) in height. Length is determined by chosen rank. Rank tile dimensions and spacing are appropriate and proportional to the sizing of the bar to allow for even spacing from each other and the border of the bar: Rogue One/Solo rank tile dimensions are approximately 15 mm wide, 21 mm tall, and 3.2 mm deep. Original Trilogy/Mandalorian rank tile dimensions are approximately ½ inch (12.7 mm) width x ¾ inch (19 mm) height x 1⁄8 inch (3.2 mm) deep. Rank tile sizes must all be of one or the other — Not to be intermixed. Please note that final dimensions of the bar may be proportional to the wearer. Rank bar corners are a hard 90 degree angle, or slightly rounded. Rank tiles are translucent, rectangular, positioned side by side in a vertical orientation, and evenly spaced. No amber/yellow tiles are present for ISB agents. Color, quantity, and combinations of the tiles/bars are determined by rank and are appropriate to uniform type/color as supported by licensed reference.  
OPTIONAL Level two certification (if applicable): Rank consists of colored plastic push buttons (with white to off white insert) mounted on a metal bar. OPTIONAL Level three certification (if applicable): Chosen rank to match a specific officer seen onscreen or other licensed media.  
   
 
 
Code Cylinders 2 per costume may be worn one in each pocket Modified: silver "chalk holder" tube with short clip, top is colored Blue. Dosimeter style: True Dosimeter with correct clip and Blue top. Ysanne Isard, Code Cylinders are not required.  
OPTIONAL Level two certification (if applicable): Only real or replica dosimeters are used. Dosimeters have a silver, non-brass, clip  
   
 
Belt The belt is constructed from a non-textured leather or a leather-like material. Approximately 2" (50.8 mm) in width, up to 3" (76.2 mm) is acceptable. There are no loops on the belt. A single large snap or rivet is visible approximately 1" (25.4 mm) from the buckle. The belt may be worn with the snap to the right or left of the wearer. The buckle is constructed from a horizontally brushed metal, or metal looking material. The buckle size is approximately 2 ⅛" (66.7 mm) high and 4 ⅛" (104.5 mm) wide with 0.5" (12.7 mm) radius rounded corners. Buckle is adorned with an Imperial Code Disk at the center. Please refer to the Imperial Buckle reference page for information on accurate and inaccurate style buckles.  
OPTIONAL Level two certification (if applicable): Belt is made of leather. Snap is worn to the left of the wearer. Buckle has a slight horizontal curve.  
   
Belt boxes (Non-Saga style) Dimensions are approximately 2 inches (50.8mm) wide by 3 inches (76.2 mm) tall by 1 inch x (25.4mm) thick. Two boxes to be worn vertically, one each on either side of the belt buckle.  
OPTIONAL Level two certification (if applicable): Belt boxes are made of metal.  
   
Jodhpur Trousers, Black Fabric is a medium weight suiting material matching the tunic. Cavalry Twill or a Gabardine style weave is most accurate. Version One trousers are flared riding breeches, with semi-stiff flares to the hip/thigh area. Breeches are worn with boots. Breeches are neatly pressed or ironed without creases. Pockets are acceptable, although must not be visible with the tunic on.  
 
 
Officer Boots Knee-high, black, riding style, lace-less, smooth non-textured, leather or leather-like material. There are no buckles, snap tabs or decoration. Boots have conservative heels. A single stretch panel or zipper may be present, they are to be hidden on the inner part of the boot shaft. Not visible from the front, side or back. The top of the boots may be flat or Spanish Style, but not Cowboy or Super Hero (pointed at the front) style. A small V-shaped notch may be present that the back of the boots top.  
OPTIONAL Level two certification (if applicable): Boots do not have a zipper. OPTIONAL Level three certification (if applicable): Boots are made of leather. Not vinyl or PVC. Exact replicas of English riding (dress) boots or Equestrian boots.  
   
Optional Accessories Items below are optional costume accessories. These items are not required for approval, but if present appear as described below. If adding in an accessory after initial approval, the item still needs to be submitted to local GML for approval before use.
 
200x150px Epaulets, Silver Silver, colored strips, firmly attached on the edge of each shoulder. The strips are matte or metallic in finish and made with a semi-rigid to rigid material. The strips have a small raised ridge around the edge. The strips are no more than 1.25 inches in width. Positioned across the collar bone where the shoulder begins, between the shoulder seam and yoke seam. The strips do not overlap the seams they sit between.  
OPTIONAL Level two certification (if applicable): The lower limit of the strip, in positioning, should run parallel to the lowest point of the center of the collar. OPTIONAL Level three certification (if applicable): Have a metallic sheen.  
   
Holster Made of black leather or leather-like material.  
OPTIONAL Level two certification (if applicable): Holster is affixed via a single loop over the belt. Holster is made of leather.  
   
SE-14R Light Repeating Blaster The barrel detailing is evident with the cocking lever and slider in place. The ejection port is also evident. The scope mount looks similar to the magazine but smaller in size. The scope does not protrude past the blaster body.    
 

I have a picture coming, but here's the draft text for the epaulets. 
 
 
Epaulets, Silver Dark silver, colored strips, firmly attached on the edge of each shoulder. The strips are matte or metallic in finish and made with a semi-rigid to rigid material. The strips have a small raised ridge around the edge. The strips are no more than 1.25 inches in width.  Positioned across the collar bone where the shoulder begins, between the shoulder seam and yoke seam. The strips do not overlap the seams they sit between.  
OPTIONAL Level two certification (if applicable): The lower limit of the strip, in positioning, should run parallel to the lowest point of the center of the collar. OPTIONAL Level three certification (if applicable): Have a metallic sheen.

This looks brilliant!! @RobinKrennicDutch
 Did you make this trenchoat from a pattern yourself? 
I'd love to attempt to sew one  myself in the future
so happy were getting all this new ISB content in Andor. 
 
please feel free to share these pics on the "non saga isb optional accesories" post, as well, they could really help us with the upcoming crl were putting together  
 
 

That would be great! 

Hello guys,

I made a first try on the trench coat that can be seen on the Andor trailer. It looks good on the ISB but I am not quite happy with it myself as its now. 

I'd love to hear what you think of it. Here are the pictures

I think it looks really good!

Thanks! All I did was provide the unmatchable rugged good looks.  
 
The actual talent here is @Alay

looks amazing @chicken45, will be great to see all these new CRL editions in the near future.  

Got a better picture:
 
Untitled by josh_surkosky, on Flickr

The Imperial Military Department of Advanced Weapons Research (AWR) is one of the ten branches of the ISB (The ISB is then a sub-group of COMPNOR). That's why Krennic wears the black and white uniform. He just takes some liberties with the boots, trousers and the cape (Mainly because he's so insecure )
The old intelligence agencies were merged into the Ubiqtorate which falls under Imperial Intelligence.

It's a strange relationship with a lot of rivalry between I.I and I.S.B , but they still play nice (ISB gets to use II Deathtroopers etc.).

Hi everyone
 
Im currently already working on a non saga officer, for my next 501st costume, but after seeing the new Andor teaser, its got me really interested in also making an ISB uniform.
I have a quick question about this, as with the current "version 3" ISB costume from Rogue One, gloves are not an optional accesory, and I just wanted to ask if these photos from both the Andor trailer and prodcution shots, may shed any new light on this? 
Im only guessing here, but they appear to be wearing the same style uniform as the RO isb, with the code cylinders etc.  the tunics look white, again same as the RO version, but could be a trick of camera light.
there does seem to be some new rank bars as well , but only one variant, (5 blue squares) is clearly visable so far . 
 
any advice on this would be great, as I'd would be interested in making this costume. 
 
Thanks everyone,  
 

Epaulette looks amazing!!, I think I may need to purchase a pair myself in the future
I recently got the same rank bar as well, 

I'm ready!
I snapped a quick pic of @Alay's epaulette beta.

Could be right, I had forgotton that military intelligence had a similar uniform. 
Will definitely be interesting to see them when the series is released. 
Looks like they are sticking with the new "white" fabric that they used for Krennic and R1 ISB. Rather than the Cream from ANH. 
 
worst case is if it does turn out they are intelligence and not ISB, we can still use these photos to help with the CRL. 

Hello, I am posting here the first draft of a CRL for the "Camino Clone Medic" for discussion.
The images for this can be seen in the link
 
costume pics
https://photos.app.goo.gl/UcUjjSTv69CJMorZA
Source photo
https://photos.app.goo.gl/FHAMd9sXrMmzqGtYA
Detail photo
https://photos.app.goo.gl/BwkBzEG8VnceJWg76
 
 
cap, white
Cloth is a medium-weight suit material that matches the tunic and pants perfectly.
Weaving in gabardine style is the most accurate.
Color matched to tunic and trousers.
The base of the hat is tapered, with a crown approximately 4" (101.6mm) high.
Front and rear "flaps" overlap at the sides and are approximately 4 inches (101.6mm) high.
The front beak extends down 3 inches and is decorated with (5) (6) or (7) concentric stitches.
Imperial Code Disk in the center of the front vertical "flap".
At the bottom of the front flap there is a red stripe 1.5cm wide, the same red as the stripes on the sleeves.
 
OPTIONAL Level 2 Certification (if applicable):
The code disc has a notch on the outermost disc.
OPTIONAL Level 3 Certification (if applicable):
Code Disk exactly matches the prop used by the screen.
tunic
White fabric is a mid-weight suit fabric that matches the pants perfectly.
The tunic is double breasted with a left over right closure at the tapered yoke.
The yoke extends over the shoulder to the upper shoulder seam.
The stand-up collar has square corners with a left-over-right center closure.
The collar contains a modesty panel.
The tunic has medium gray matt satin piping.
On each shoulder are rectangular epaulettes in the same gray as the piping.
The sleeves are long and without cuffs or buttons.
Sleeves contain 1 seam, on the inside.
On both sleeves there are two rank bands made of gray faux leather in the same gray as epaulettes and piping.
The tunic is constructed without topstitching (seams are visible on the outer surface of the fabric).
The back of the tunic has a seam that runs down the center of the tunic from the neck to the hem.
There is a slit on the back of the tunic that runs from belt level to the floor.
On the outside of the sleeves, two parallel red stripes, as wide as the rank stripes, run the length of the sleeve from the epaulette to the cuff. The total width of the two stripes ends with the width of the epaulette.
On the right chest is the Kamino Doctors patch.
 
OPTIONAL Level 2 Certification (if applicable):
•The collar is approximately 3.175 cm (1.25") to 6.35 cm (2.5")
 
OPTIONAL Level 3 Certification (if applicable):
• Tunic fastens on the right side with snaps or buttons.
• No stitching is visible anywhere.
• A lining is sewn in.
• The shoulder lines look very straight.
 
trousers
White fabric is a medium weight suiting fabric that matches the tunic perfectly.
The trouser legs are straight, without rider flaps, and are worn tucked into the boots.
Pockets are acceptable but must not be visible when the tunic is on.
 
rank bar
The rank bar is worn on the left side of the tunic over the piping.
Rank consists of colored plastic tiles mounted in a frame panel.
The rankbar consists of three tiles in a row, one blue tile on the right and two red tiles on the left.
 
OPTIONAL Level 2 Certification (if applicable):
The bar is approximately 1⅛" (28.6 mm) high.
The length of the frame plate is approximately 6 cm (2⅓") wide
The dimensions of the rank plates are approximately ⅝" (16 mm) wide x ⅞" (22 mm) high.
 
Belt
The belt is made from a non-textured brown leather or leather-like material in the same brown as the boots and is approximately 51mm wide.
•There are no loops on the belt.
•The buckle has rounded corners and is made of a horizontally brushed metal or metal-like material.
The buckle is embellished with a Republican code disc in the center.
•The code disc is a stepped cone shape that looks like 2 discs stacked on top of each other. • The larger disc is 1.4 inch (3.5 cm) and the smaller disc is 1 inch (2.5 cm).
 
Boots
The boots are made of brown leather or leather-like material, the same brown as the belt.
If stretch inserts or zippers are present, they must be hidden on the inner shaft.
Boots have a wider arch on either side of the ankle.
The upper edge of the shaft is shaped as a cuff.
 
OPTIONAL Level 2 Certification (if applicable):
Boots do not have a zipper.
Boots are made of leather.
 
Optional
 
gloves
Gloves are made of brown leather or leather-like material, the same brown as boots and belts.
Gloves can be plain or have 3 stitch lines on the back of the hand.
 
DC-15S blaster
Manufactured by BlasTech Industries, the DC-15S is smaller than the DC-15A blaster rifle. Although it has a shorter range than the "A" model, it is easier to handle with a higher rate of fire. It features a folding stock for braced shooting.
 
Realistic clone style DC-15S blaster.
Blaster can be custom built out of plastic, wood, metal or cast in resin.
Blaster has realistic Episode II or Episode III details:
wire frame sight.
Collapsible storage.
Twelve (12) radiator fins evenly spaced along the length of the cylinder.
Igniter detail buttons.
Load the magazine clip on the right.
The overall length is approximately 26" (66 cm).
Due to the scaling, the Hasbro version is wrong.
 
OPTIONAL Level 2 Certification (if applicable):
The detail of the loading magazine on the clip is gun metal color gun metal.
Detail studs and screws are gun metal gray in color.
Ignition knobs have some copper tint.
Blaster is weathered.
OPTIONAL Level 3 Certification (if applicable):
Working blue LED is installed in the barrel.